Model rockets are stable when they move under power in the direction that they are initially pointed. Similar to an arrow, a model rocket has fins on a long body. The fins add a large surface area to the rear of a model rocket that increases the air resistance and moves the center of this resistance towards the rear of the rocket. The center of all the resisting forces on a model rocket is called the center of pressure.

A model rocket or any object moving through the air will rotate around its axis at the center of the weight distribution. This is called the center of gravity. This is where the rocket balances horizontal to the ground when you hold it loosley by the tips of two of your fingers. On a model rocket, the center of pressure (CP) needs to be behind the center of gravity (CG) for the rocket to be stable.

As a rocket is pushed through the air, the center of air resistance (CP), rotates behind the center of rotation (CG), causing the rocket to point forward. Because of this action, the rocket is pointed into the relative wind during flight.

Generally, the distance the CG should be ahead of the CP is equal to 1 or 2 times the diameter of the body of the rocket. Being closer than this could cause the rocket to wobble or even try to reverse its direction by looping in flight. Being farther than this could cause the rocket to be overly stable and veer off into a moderate wind instead of going straight up. This behavior is called “weather-vaning.” Of the two options, over stability is more desirable.

Finding the CG on a rocket, large or small, is relatively easy. Finding the CP is more difficult. One of the easiest methods for determining the stability of model rocket is to tie a loop of string around the CG of a model rocket and swing it around your head to see if the rocket is stable. This is called the “Swing Test”. This method works on smaller rockets, but does not necessarily prove that a larger rocket is stable or unstable. This is due to practical limits on the length of a string you might be able to swing around your head.

**Example 1:**At 10 feet of string length, a 24 inch rocket has the nose and tail moving through the relative wind at an angle of 2.9 degrees from ideal, or a total difference between the nose and the tail of 5.8 degrees. A rocket of this length will probably be able to be tested at this length.

**Example 2:**At 10 feet of string length, a 48 inch rocket has the nose and tail moving through the relative wind at an angle of 5.8 degrees from ideal, or a total difference between the nose and the tail of 11.6 degrees. A rocket of this length has too much angular distance between the nose and the tail relative to the forward motion in the wind and probably would not be able to be tested at this string length.

Large or heavy rockets are difficult to swing and could be damaged if the rocket hits a stationery object or person during the test. A better way of determining the stability of rocket is to determine the CP by calculation. One of the best known methods is called the Barrowman method.

**Barrowman Method of Predicting Stability**

The Barrowman method calculates all the individual pressure changes along the rocket from nose to tip. After each change is calculated, the total of each element is added and a ratio is calculated from the same elements multiplied by the force value for each element.

To use the equations, the values measured from the rocket as illustrated above are substituted into the equation. Refer to the definitions below while taking measurements:

L

d

d

d

X

C

C

S = Fin Span

L

R = Radius Body at End

X

X

N = Number of Fins

While this task seems daunting it can be done in stages using a calculator with square root capability. If you don't want to go to this trouble, you can download a free Winroc windows based software program the from our website at ModelRockets.us that can do this for you.

The following terms are substituted for general math symbols:

* = Multiplication Function

/ = Division Function

^ = Square Function

Sqr = Square Root Function

C

Here the CP value represents the center of pressure. Use the following factors and calculations and then plug the numbers in the Barrowman Basic Equation above (repeated at the end of this blog).

All Shapes of Nose Cones: C

For Conical Nose Cones: X

For Ogive Nose Cones: X

For Parabolic Nose Cones: X

For Hack Nose Cones: X

For Von Karmen Nose Cones: X

C

X

The LF value is needed for trapezoidal fins only. It can be measured or calculated with the following equation:

L

FT1 = 1 + (R / (S + R))

FT2 = 1 + Sqr(1 + ((2 * L

CNF = FT1 * (((N * 4) * (S / d) ^ 2) / FT2)

FT3 = C

FT4 = (FT3 - ((C

X

FT5 = (4 * N * (S / d) ^ 2) / (1 + Sqr(1 + (1.623 * (S / CR ) ^ 2)))

C

X

After calculating each element of the rocket. They are applied in the final equation:

C

Use the CP value measured from the tip of the nose cone of your rocket. This location is the center of pressure of your rocket. If your rockets CG is 1or 2 tube diameters ahead of the CP then most cases your rocket will be stable and you are ready to go.

There is an exception to the CP to CG distance rule that applies to short fat rockets. These kind of designs can often fly very well with a CP to CG distance of 1/2 to 1 tube diameter.

L

*N*= Length of Nose d = Diam. of Base Nosed

*F*= Diam. of Transition Frontd

*R*= Diam. of Rear Transitiond

*T*= Diam. of Rear TransitionX

*P*= Distance to TransitionC

*R*= Fin Root ChordC

*T*= Fin Tip ChordS = Fin Span

L

*F*= Fin Mid-chord LineR = Radius Body at End

X

*R*= Fin SweepX

*B*= Distance Nose to FinN = Number of Fins

**Barrowman Calculations**While this task seems daunting it can be done in stages using a calculator with square root capability. If you don't want to go to this trouble, you can download a free Winroc windows based software program the from our website at ModelRockets.us that can do this for you.

The following terms are substituted for general math symbols:

* = Multiplication Function

/ = Division Function

^ = Square Function

Sqr = Square Root Function

**Barrowman Basic Equation**

C

*P*= (C

*NN** X

*N*+ C

*NT** X

*T*+ C

*NF** X

*F*) / (C

*NN*+ C

*NT*+ C

*NF*)

Here the CP value represents the center of pressure. Use the following factors and calculations and then plug the numbers in the Barrowman Basic Equation above (repeated at the end of this blog).

**Calculating the Nosecone Values**

All Shapes of Nose Cones: C

*NN*= 2

For Conical Nose Cones: X

*N*= 0.666 * L

*N*

For Ogive Nose Cones: X

*N*= 0.466 * L

*N*

For Parabolic Nose Cones: X

*N*= 0.5 * L

*N*

For Hack Nose Cones: X

*N*= 0.5 * L

*N*

For Von Karmen Nose Cones: X

*N*= 0.563 * L

*N*

**Calculating the Transition Values (if there are any)**

C

*NT*= 2 * (((d

*R*/ d) ^ 2) - ((d

*F*/ d) ^ 2))

X

*T*= X

*P*+ ((L

*T*/ 3) * (1 + ((1 - (d

*F*/ d

*R*)) / (1 - (d

*F*/d

*R*) ^ 2))))

**Calculating Fin Values**

The LF value is needed for trapezoidal fins only. It can be measured or calculated with the following equation:

L

*F*= Sqr (S ^ 2 + (X

*R*+ (C

*T*/ 2) - (C

*R*/ 2)) ^ 2)

**Trapezoidal Fins**

FT1 = 1 + (R / (S + R))

FT2 = 1 + Sqr(1 + ((2 * L

*F*) / (C

*R*+ C

*T*)) ^ 2)

CNF = FT1 * (((N * 4) * (S / d) ^ 2) / FT2)

FT3 = C

*R*+ C

*T*

FT4 = (FT3 - ((C

*R** C

*T*) / FT3)) / 6

X

*F*= X

*B*+ ((X

*R*/ 3) * ((FT3 + CT) / FT3)) + FT4

**Elliptical Fins**

FT5 = (4 * N * (S / d) ^ 2) / (1 + Sqr(1 + (1.623 * (S / CR ) ^ 2)))

C

*NF*= FT5 * (1 + R / (S + R))

X

*F*= X

*B*+ 0.288 * CR

**Final Results**

After calculating each element of the rocket. They are applied in the final equation:

C

*P*= (C

*NN** X

*N*+ C

*NT** X

*T*+ C

*NF** X

*F*) / (C

*NN*+ C

*NT*+ C

*NF*)

Use the CP value measured from the tip of the nose cone of your rocket. This location is the center of pressure of your rocket. If your rockets CG is 1or 2 tube diameters ahead of the CP then most cases your rocket will be stable and you are ready to go.

**Note:**

There is an exception to the CP to CG distance rule that applies to short fat rockets. These kind of designs can often fly very well with a CP to CG distance of 1/2 to 1 tube diameter.

For more information go to ModelRockets.us